The contact owns a 2023 Mercedes Benz EQE. The contact stated that after the vehicle was delivered to his residence the low coolant warning light illuminated. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was 328. The VIN was not available.

Complaint Yellow instrument cluster message: Cooling system fault, operating energy input reduced, service required. Cause Fault code B3A0077 - The regulation valve in the refrigerant circuit for the battery cooling gets stuck open. The ordered position cannot be achieved stored. Faulty expansion valve component part Y140/1 Remedy Check the part number of Y140/1. If the vehicle has A 297 830 79 03 or older, replace Y140/1 with A 297 830 89 03 or newer. Do not replace defective components with part number A 297 830 8903 and an expansion valve production date after February 1, 2025! Please create TIPS case, attach the current quick test and attach picture of the evaporator assembly component part label and a picture of the production date of the EXV Y140/1 (see exampled attached).

Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal brake pad and brake rotor vibrations. Exchanging brake components will not rectify.

Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment. Note: Please refer to this document in the warranty claim and, once diagnosis is completed, select the damage code depending on the component part that is causing the issue. • If the noise stops when the door trim is removed, please proceed in accordance with LI72.10-P-067691. Note: In this case, do not use the damage codes for the speakers in the warranty claim.

Complaint The Easy entry and exit feature function deactivates itself after a brief period. (see attachment). Cause The cause is currently being investigated. Remedy Update the HU7 to the latest software version, then perform a factory reset of the HU7. Steps to perform factory reset: Navigate to Settings > System > Reset > Reset to factory settings and confirm. If the problem persists, please record HU7 log and also a trace of the Body CAN (For Star 2 Body Can 1 and for Star 3 Body Can 2) during the symptom and send via a TIPS case to the Telematics team. Note: Only collect and submit the log and trace if the symptom can be reliably reproduced.

Complaint The OTA software update prepares the SRS/ORC controller and enables it to be updated remotely in the future. Based on technician feedback, the OTA (code: 25P5496529) does not start even after an extended period of time and several driving cycles. In addition, the Continue button is grayed out. Cause The exact cause for the OTA not to start is currently under analysis. Remedy Please check whether the vehicle is affected by the field measure Update software of Supplemental Restraint System (SRS) control unit (code: 25P5496529) and if yes, perform this update using a XENTRY  with all latest Add-Ons and bill under accounting number 5496529. If the vehicle is not affected by this field measure, in the event of a complaint update control unit ORC223 (N2/5 -Supplemental Restraint System SRS) using XENTRY and use damage code 8251M01. As of XENTRY Release Version 06/25, control unit ORC223 can also be updated in this context without a password. Provided control unit ORC223 is error-free after the update, the vehicle can be handed back. ***IMPORTANT*** -In isolated cases, the OTA update may continue to be displayed for up to 3-4 weeks even after flashing with XENTRY. Note: This LI applies only to the OTA update for occupant protection!

Complaint One of the flush door handles (Also referred to as Seamless Door Handles) does not extend/retract (and/or) the KeylessGo sensor surfaces do not respond. Cause Multiple possible causes can be inferred from the table, see remedy (additionally as reference table in attachment). Remedy 1) KeylessGo sensor surfaces do not respond. Door handles can extend/retract if the key is used for locking/unlocking. No particular fault code. Perform an A17/x (handle controller) reset via XENTRY (for example see attachment - under actuations tab for A17/x controller) -> add-on is available (add-on 32204 for XENTRY version 06/25) Please use one of the following damage codes: 8213H; 82197; 8213K; 82198 2) Surface-flush door handle fails to retract and/or extend One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 A control unit event log for the component part concerned (A17/x) must be created and the following values checked in the Component Errors section: Motor_bridge_connection_fatal_error = True (for example, see attachment) OR Motor_bridge_wrong_direction_fatal_error = True (for example, see attachment) If one of the values is True: Perform an SCN coding on the door handle A17/x via XENTRY -> add-on is available (add-on 32280 for XENTRY version 06/25) The faults must be deleted after SCN coding. Please use one of the following damage codes: 80A0F; 80N0F; 80N0G; 80A0G 3) Surface-flush door handle fails to retract and/or extend One or more of the following fault codes are current and stored: B185D96; B185E96; B186196; B186296 A control unit event log for the component part concerned (A17/x) must be created and the following value checked in the Component Errors section: Motor_init_error_for_sensors = True (for example, see attachment) If the value is True Bearing bracket must be replaced. Please use one of the following damage codes: 80A0F; 80N0F; 80N0G; 80A0G 4) Surface-flush door handle fails to retract and/or extend The fault code B185911 is stored in the DCU (N69/X). The motor resistance is too low. Bearing bracket must be replaced. Please use one of the following damage codes: 80A0D; 80N0D; 80N0E; 80A0E If after the remedy points above are performed and the problem is still present, then please create a TIPS case and direct to the Body/Chassis/Entertainment inbox. Include your control unit logs, photos/videos, and quick tests to show diagnosis performed thus far. -> In this case, store the damaged parts for further analyses.

Complaint Users report that the browser no longer supports search queries entered directly into the address bar. Cause This update is due to Microsoft discontinuing the Bing Search API, which previously supported this feature. Remedy This behavior is considered consistent with current system design and reflects the intended functionality. No corrective action is required. Additional Information: Despite the removal of address bar search capability, users retain full access to standard browser features, including: • Direct entry of website URLs • Use of search functions provided within individual websites

Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has updated driver assistance system SCN coding available for certain subject vehicles. The updated SCN coding improves system stability and enhances the availability of driver assistance features.  MBUSA will conduct an OTA service campaign. Remote SCN coding updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Complaint Reduced Drive Power' warning displayed on Instrument Cluster, as Illustrated in the Picture, but no relevant fault codes are present. Cause There are several reasons for the activation of the Reduced Drive Power Warning, Here are a few examples: • Hood is not closed properly • Valet Service Mode is activated • Beginner Driver Mode is activated Remedy If no relevant fault codes are present, first ensure the hood is securely closed and verify that neither Valet Service Mode nor Beginner Driver Mode is activated in MBUX. If relevant fault codes are detected, then proceed with diagnosing and resolving those specific faults.

Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the ignition lock (EZS) control unit does not correspond with the latest series production configuration. The EZS control unit will receive an OTA software update which will improve the performance of hands-free access on the affected vehicles. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.

Mercedes-Benz EQE 350

Filing history

Top reported issues — Mercedes-Benz EQE 350

Recent filings